!9#: DEWALT DW716 15 Amp 12-Inch Double-Bevel Compound Miter Saw

Brand : DEWALT | Rate : | Price : Too low to display
Post Date : Dec 29, 2011 04:36:11 | Usually ships in 24 hours

DEWALT DW716 15 Amp 12-Inch Double-Bevel Compound Miter Saw

• 15.0 Amp, 3,600 rpm motor delivers extended power and durability
• Adjustable stainless steel miter detent plate with 11 positive stops Improves productivity and ensures cutting accuracy
• Precise miter system and machined base fence support optimize cutting accuracy
• Tall sliding fences support crown molding up to 6-5/8-inch nested and base molding up to 6-1/2-inch vertically against the fence while easily sliding out of the way for bevel cuts
• Innovative gearbox and belt-drive design increases vertical cutting capacity

More Specification..!!

DEWALT DW716 15 Amp 12-Inch Double-Bevel Compound Miter Saw

Bose Cinemate Series Ii Digital Home Theater Speaker System Purchase

How to Install a Shower Faucet in 7 Easy Steps

!9#: How to Install a Shower Faucet in 7 Easy Steps

Installing a shower faucet is not a herculean task. If you know the right tricks it is as easy as conjuring up a rabbit in mid-air. Here is how to install a shower faucet in 7 easy steps.

Before starting the installation here are few things you need to take care.

Check the supply pipe for leaks. Replace wall with moisture resistance dry wall as base for wall covering. Always clean the pipe thread and apply a new pipe joint compound. Run hot and cold water lines to shower mixing valve attached. Plan for a trap door in wall.

These are just a few pointers you need to take care before installation. Now let us begin the installation.

First you can connect the shower in two ways. You can either choose the conventional method with copper pipes or you can opt for PEX pipes. The plastic pipes are easy to install when compared to the copper pipes. The next thing you need to do is the shut off the water supply and drill a hole in the shower walls with a hole saw. It is better to plan before hand where to install the shower and the faucet and mark them with a pencil. Now position the valve so that UP indication points upward and then connect the hot and cold water pipes to each side of the valve. When welding them take care to see that overheating does not take place. You can also use welding adapters if required. Secure the valve inside the wall and connect the raise tube and spout pipe in welded adapters. If valve is without spout then use a brass cap to block the outlet that will not be used. Put the shower in place. This completes the installation of the valve. Next to install the faucet handle slide the decorative plate in the valve and position the handle screw adapter on cartridge using hexagonal key. Now to install the shower head connect the upper outlet to shower head supply pipe after applying Teflon tape. Wrap clockwise the shower head's pipe filets with Teflon tape. Manually screw shower head using adjustable wrench. Finally to install the spout turn the spout on copper pipe so that set screw faces up. Tighten the screw with hexagonal key and then turn spout to normal position. Last but not the least open the hot and cold water supply and check if there is no leak. Next open the faucet to lukewarm position to release all the air caught in the pipes.

That's it. You are done. Now you can show off your skills to your wife or your neighbor.

How to Install a Shower Faucet in 7 Easy Steps

Cheaper American Girl Doll Bunk Beds

Woodworking For Fun And Profit Is A Great Hobby

!9#: Woodworking For Fun And Profit Is A Great Hobby

If you like working with your hands, woodworking is a good hobby for you. It is easy to get started at this enjoyable pastime. You just need a few simple tools, some hardware, a little education and some practice. As you progress you can get more woodworking tools, hardware. The more woodworking projects you work on, the more your skills will improve. The possibilities of things that you can make woodworking are endless. While enjoying your hobby, you can make clocks, chess boards, flag boxes, and toys, among other things.

Tools - Some tools you might want to have for your hobby or pastime are table, radial arm, chop or sliding compound miter saws. In addition to saws, you may need chisels, planes, rasps, scrapers, clamps and many types of jigs for woodworking. These woodworking tools will make your projects accurate. You will also need hardware such as hinges, screws and ball bearings.

Getting Started With Woodworking - After you have some woodworking tools, you will need to select some wood for your project. Once you have the tools and the wood, you can get started with your first woodworking project. One method to learn the craft is to make the same project over and over until you are satisfied with the results. This works best for smaller projects. For larger projects, or if you are not a perfectionist, make one woodworking project and then move on to your next task.

There are several good ways to learn about woodworking. There are wookworking videos, books, websites and clubs that can all help you get started with working with your hands. Woodworking plans are available for all sorts of projects from these sources as well as from hobby stores. Plans are available for both large and small projects.

Using Woodworking to Make Gifts - Your family and friends will learn to appreciate receiving gifts from you that made yourself while woodworking. Rather than receiving something less personal bought from a store, they will be receiving something into which you put your time, effort and heart. They will be able to cherish these handmade gifts for years to come. If you are working on larger projects, your family and friends may start requesting you to build them a table, cabinet, breakfront, bed or other wooden furniture item. The time to get started on a project is now. Gather the tools, hardware and wood and obtain some plans and know-how.

Woodworking For Fun And Profit Is A Great Hobby

Powered Subwoofers Reviews Save Great Deals Black And Decker Wrenches Purchasing Mk Tile Saw Parts

dw718

!9#: dw718

Sierra Ingleteadora 12" para trabajo pesado para más info. www.ferremayoreo.com.mx Características y Beneficios Potente motor de 15 amp. y 4.000 rpm que ofrece mayor potencia y durabilidad Placa de retención de inglete regulable, de acero inoxidable, con 11 topes positivos, que garantiza precisión sostenida y durabilidad en la obra Sistema de inglete exclusivo y preciso y soporte para guía de base maquinada que brindan mayor exactitud en el corte Guía deslizante que da soporte a las molduras de corona de hasta 133,4 mm (5-1/4") insertadas ya las molduras de base de hasta 165,1 mm (6-1/2") en forma vertical contra la guía mientras que se desliza fácilmente para dar lugar a cortes biselados Biselado de 0º a 48º a la izquierda y de 0º a 3º a la derecha para mayor capacidad Capacidad de ingleteado de 0º a 50º hacia ambos lados para mayor versatilidad Para más información consulte www.ferremayoreo.com.mx donde encontrara toda la información correspondiente a este equipo fotos, ficha técnica, manual del usuario completo, diagrama (despiece o explosivo) con códigos de partes.

dw718

Stairmaster 4600pt This Instant